Загрузил antoniucvova

Service Manual SB-9 v1.00 work normal

реклама
Leading Image Processing Technology
We've been there when you needed
Service Manual
SB-9
SBM Co., Ltd.
Ver. 1.00
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Important Safety Information
Always be careful when using the machine. To reduce the risk of fire, electrical shocks, and other injuries, keep
these safety considerations in mind when installing, using, and maintaining your machine:
Stability :
Place the machine on a secure, stable surface. The machine can be seriously damaged if it falls.
Power Supply :
Provide correct power to the machine, as listed on the back of the machine. If you are not sure
of the type of power that is supplied to your office, call your electric company.
Grounding :
If the plug has three prongs, it must be plugged into a grounded (three hole) outlet. Grounded
plugs and outlets are designed for your safety - do not try to make a three-prong plug fit into a
two-prong outlet by modifying the plug or outlet in any way. If you cannot insert the plug into your
wall outlet easily, then a qualified electrician should inspect the outlet.
Overload :
Do not plug too many electrical devices into a wall outlet or an extension cord. An overloaded
outlet could be a reason of a fire and electrical shock hazard.
Cleaning :
Before cleaning the machine, unplug it from the power outlet. Clean exposed parts with a soft
cloth slightly dampened with water. Do not use aerosol cleaners.
Gas Leaks :
Never use any machine close to a gas leak. If you think gas is leaking, call the gas company
immediately. A small electrical spark in the machine could cause a fire or explosion.
Precaution
When using the machine, these precautions should always be followed:
1.
Never push objects of any kind into your machine through the case or cabinet openings.
2.
Do not use your machine near water, in wet locations, or outdoors.
3.
Do not allow anything to rest on the power cord, line cord, or PC interface cable. Do not locate your machine
where the cords can be damaged by persons’ walking on them.
4.
Do not allow pets to chew on the power cord or PC interface cable.
5.
Use supplies or cleaning materials only as directed. Keep all supplies and materials out of the way of children.
6.
The power supply turns this machine on and off. Make sure that your machine is installed near an outlet and is
easily accessible.
7.
Never remove covers or guards that require a tool for removal. There are no operator serviceable areas inside
your machine. Refer servicing to authorized service personnel.
8.
Never defeats interlock switches. This machine is designed to restrict operator access to unsafe areas. Covers,
guards and interlock switches are provided to ensure that the machine will not operate with covers opened.
9.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to
the instruction.
-2-
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Managing the performance of the machine
This unit has many sophisticated sensors. Without proper maintenance, it cannot last its good performance. Please
read the “Daily Maintenance” section of this manual carefully, and do it everyday. When the performance is
deteriorated on a sudden, please clean all the sensors first before calling a service.
Safety Notes
Your machine and the supplies are designed and tested to
WARNING
meet strict safety requirements. Included are safety agency
Hazardous moving parts!
Keep fingers and other body parts
away
examination and approval and compliance to established
environmental standards. Please read the following
instructions carefully before operating your machine, and refer
to them as needed to ensure the continued safe operation of your machine.
Battery is used for ‘PBA POWERIO’ in this
machine. If wrong date and time are
displayed on LCD after correct setting, it is
necessary to change the battery of ‘PBA
POWERIO’. Please read the following
CAUTION
Risk of explosion: if battery is replaced by an
incorrect type. Dispose of used batteries according to
the instructions.
instructions carefully before changing the
battery.
Refer to the below Icons before reading Manual.
Icon
Explanation
Icon
Explanation
Language of Service Manual
Check
(English)
Caution
Button on Control Panel
prohibition
In order of process
-3-
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Recommended Tools
Picture
Description and Size
Picture
Description and Size
L Wrench
Hexagonal Screwdriver
Ø1.5
5mm
L Wrench
Screwdriver(-)
Ø2
6mm
Spanner
Screwdriver(-)
7mm
1.5mm
Screwdriver(-)
Nipper
2.5mm
Screwdriver(+)
Long-nose
Ø6
-4-
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Table of Contents
Chapter 1
------------------------------------------------------------------------------------------
7
Unpacking List -----------------------------------------------------------------------------------------
7
Choosing a Location ---------------------------------------------------------------------------------
7
Handling the Machine -------------------------------------------------------------------------------
7
Power Cord --------------------------------------------------------------------------------------------
8
Printer ---------------------------------------------------------------------------------------------------
8
Description of the Parts ---------------------------------------------------------------------------
9
Out Side -------------------------------------------------------------------------------------------------
9
Interface port -------------------------------------------------------------------------------------------
9
Sensors -------------------------------------------------------------------------------------------------
10
Rollers ---------------------------------------------------------------------------------------------------
11
Overview of Control Panel ---------------------------------------------------------------------
13
Operation Panel ---------------------------------------------------------------------------------------
13
Key Define ----------------------------------------------------------------------------------------------
13
Reject Reason and Error Message ------------------------------------------------------------
14
Reject Reason -----------------------------------------------------------------------------------------
14
LCD Error Messages --------------------------------------------------------------------------------
15
Chapter 5
Connection Diagram -------------------------------------------------------------------------------
16
Chapter 6
S/W Version Check ---------------------------------------------------------------------------------
17
Chapter 7
SERVICE MENU1 ------------------------------------------------------------------------------------
18
Chapter 8
SERVICE MENU2 ------------------------------------------------------------------------------------
21
Chapter 9
Shading ------------------------------------------------------------------------------------------------
24
UV SHADING ------------------------------------------------------------------------------------------
26
MR SHADING -----------------------------------------------------------------------------------------
28
CIS SHADING -----------------------------------------------------------------------------------------
31
IR SHADING -------------------------------------------------------------------------------------------
33
ERROR -------------------------------------------------------------------------------------------------
34
Adjustment --------------------------------------------------------------------------------------------
36
Gap of ADF ---------------------------------------------------------------------------------------------
36
ADF & Pickup Roller Timing -----------------------------------------------------------------------
37
Guide Selector ----------------------------------------------------------------------------------------
37
LCD (Back light) --------------------------------------------------------------------------------------
39
Hopper Sensitivity ------------------------------------------------------------------------------------
40
Reject Pocket Sensor Level -----------------------------------------------------------------------
41
Double Sensor Level --------------------------------------------------------------------------------
43
Chapter 11
Program Update -------------------------------------------------------------------------------------
45
Chapter 12
Assembly Drawings --------------------------------------------------------------------------------
47
Chapter 2
Chapter 3
Chapter 4
Chapter 10
Installation
-5-
CURRENCY DISCRIMINATION COUNTER
Chapter 13
-6-
SB-9(2000S) SERVICE MANUAL
Cover Exp View ---------------------------------------------------------------------------------------
48
Ass'y Exp View ----------------------------------------------------------------------------------------
49
Frame Exp View --------------------------------------------------------------------------------------
50
Roller Exp View ---------------------------------------------------------------------------------------
51
Cover Door Top ---------------------------------------------------------------------------------------
52
Cover Door Top Upper ------------------------------------------------------------------------------
52
Housing Pocket ---------------------------------------------------------------------------------------
53
Ass'y Ope -----------------------------------------------------------------------------------------------
54
Plate Side R --------------------------------------------------------------------------------------------
55
Plate Side L --------------------------------------------------------------------------------------------
56
Base Exp View ----------------------------------------------------------------------------------------
57
Bkt Stacker Sensor -----------------------------------------------------------------------------------
58
Cover Top -----------------------------------------------------------------------------------------------
59
Shaft Case Detector ---------------------------------------------------------------------------------
60
Case Detector With MR -----------------------------------------------------------------------------
61
Double Sensor ----------------------------------------------------------------------------------------
62
Plate Reinforce ----------------------------------------------------------------------------------------
63
Plate Guide Upper ------------------------------------------------------------------------------------
64
Plate Guide Lower ------------------------------------------------------------------------------------
65
Exp Guide Lower-P ----------------------------------------------------------------------------------
66
Bkt Smps Bottom -------------------------------------------------------------------------------------
67
Bkt Smps Top ------------------------------------------------------------------------------------------
68
Specifications ----------------------------------------------------------------------------------------
69
CURRENCY DISCRIMINATION COUNTER
1
SB-9(2000S) SERVICE MANUAL
Installation
1-1. Unpacking List
1.
Machine
1 Unit
2.
Bill Guide
2 pcs. ( Left / Right)
3.
AC Power Code
1 pc.
4.
User's Manual
1 pc.
5.
Serial Cable
1 pc.
* Optional Items: Printer, Serial to USB A Cable, USB A to USB B Cable
1-2. Choosing a Location
To help guarantee trouble-free operation of your machine, place it on a flat, stable surface near your workstation.
Do not place your machine:

In direct sunlight.

Near heat sources or air conditioners.

In dusty or dirty environments.
1-3. Handling the Machine
When handling or moving the machine, do not lift with grasping the Reject Pocket. The picture shows how to lift the
machine correctly.
(X)
(X)
(O) Correct way to lift the machine
-7-
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
1-4. Setting Up Your Machine
1-4-1. Power Cord
Plug one end of the cord into the back of the machine and the
VERSION 01. 00
other end into a standard AC power outlet.
CHECKSUM OK
OC28
If you turn on the power switch, the machine will display version
and checksum. If there is Service Call number saved by a
service provider, the Call number will be displayed.
A/S NO.
321 7654 9876
1-4-2. Printer
Your SB-9(2000S) has a serial interface port, which allows you to connect the printer to print out counting result.
To connect the printer to the machine, follow the steps below:
1.
Make sure that both the SB-9(2000S) and the printer are turned off.
2.
Plug the cable of printer into the serial port of SB-9(2000S).
3.
Turn on the printer and SB-9(2000S).
CAUTION
In case that another port is used to avoid electrical shock, turn off SB-9(2000S) and turn on
the machine after Port is connected.
-8-
CURRENCY DISCRIMINATION COUNTER
2
SB-9(2000S) SERVICE MANUAL
Description of the Parts
2-1. Out Side
2-2. Interface Port
RS232C
(RJ-11)
LAN
(RJ-45)
RS232C
(9P D-SUB)
PORT
USB
(Type B)
USB
(Type A)
INTERFACE
RS232C (RJ-11)
Customer Display
LAN (RJ-45)
Network (100M BPS) : Optional
RS232C (9P D-SUB)
Printer or PC
USB(Type B)
PC
USB(Type A)
USB MEMORY (Firmware Upgrade )
-9-
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
2-3. Sensors
This machine uses various sensors to detect the malfunction of the machine and the status of the notes in the
machine and to recognize the denominations of the notes. The sensors are very sensitive and if they are not
cleaned correctly everyday, this may negatively affect performance of the machine.
- 10 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Clean the sensors described below everyday after operating. The power must be turned off before cleaning and
please do not use a volatile solvent for cleaning.
MDD
Note:
In case of feed roller, clean with slightly dampened cloth with alcohol. While rotating one side of the roller manually,
stick the cloth to the other side of the roller.
- 11 -
CURRENCY DISCRIMINATION COUNTER
2-4. Rollers
- 12 -
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
3
SB-9(2000S) SERVICE MANUAL
Overview of Control Panel
3-1. Operation Panel
3-2. Key Define
$ ◀▶ €
Select Currency
ADD
Add function On/Off
CF
Counterfeit Detector On/Off
BATCH
Batch function On/Off
DENOM
Select a denomination
dual user mode : Counting Start (manual mode) /
5 (START)
Stop key / Transmit data or Print
PRINT
Print
GT
Grand Total Display
Menu
Change settings or parameters / Escape from Menu
▲
Up
▼
Down
MODE
Change Mode
DISPLAY
Change Display Mode
Counting Start (manual mode) / Enter /Stop key /
START/ENTER
Transmit data or Print(In dual user mode)
C
Clear Errors / Cancel Input
Pocket LED
If some notes remain on the Reject pocket, this LED will be lit.
The function of each key could be changed.
- 13 -
CURRENCY DISCRIMINATION COUNTER
4
SB-9(2000S) SERVICE MANUAL
Reject Reason and Error Message
4-1. Reject Reason
The machine provides various information regarding counting results. Every time pressing DISPLAY key, the
display mode is changed sequentially. There are 5 views.
The last view is Reject Reason view. Below is some examples of each Display mode.
Reject Reason View
Summary of the reject reasons are as follows.
SUMMARY of the REJECT REASONS
NO I.D.
: The machine failed to identify the denomination.
NO READ
: The note was not successfully read.
OVERRUN
: The next note was fed too close to the first note.
CF
: The note was suspected to be a counterfeit.
STAY NOTE
: The note was not fit to the condition of sorting.
DOUBLE
: More than two pieces of notes were fed into machine
CHAIN
: Chain Error
HALF
: Half Error
CAUTION
If the reject reason is Chain or Half, the number of the reject note displayed
on LCD can be different with the actual number of notes in the reject pocket.
In this view, user can check only simple reject reason.
When you want see the detail reason, you can check at the Service Menu1.
Press Button: 9→MODE→***** → 7(SENSOR SELECT) → 35719 → 4(CF DETAIL) → START → Clear
Summary of the ‘NO ID’ and ‘CF’ details are as follows.
- 14 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Summary of the ‘NO ID’ and ‘CF’ details
NO ID (1) ~ NO ID (6): Asymmetrical Error
NO ID (7) ~ NO ID (10): IMAGE MATCHING ERROR
NO ID (12) ~ NO ID (13): IMAGE SACN ERROR
CF UV1: UV error in transmission
CF UV2: SUV error in transmission
CF UV3: UV error in reflection.
CF MR1: Can’t find MR signal (This area should have MR signal.)
CF MR2: Excessively detect MR signal (This area should not have MR signal.)
CF MR3: No difference between the area with MR signal and the area without MR signal
CF IR1: Can’t find IR signal (This area should have IR signal.)
CF IR2: Excessively detect IR signal (This area should not have IR signal.)
CF IR3: No difference between the area with IR signal and the area without IR signal
CF IR4~5: For Developer
4-2. LCD Error Messages
Display
CHECK FRONT AREA
CHECK REAR AREA
FEED MOTOR ERROR
MAIN MOTOR ERROR
CLEAR HOPPER
CLEAR REJECT POCKET
CLEAR STACKER POCKET
FEEDING ERROR
JAM1
JAM2
JAM3
JAM4
Meaning
Front Cover is opened
banknotes are inside
Rear Cover is opened or
banknotes are inside.
Feed Motor stopped.
MAIN Motor stopped.
Notes exist in the Hopper.
Notes exist in the Rejecter
Notes exist in the Stacker
Miss-feeding Error
Jam Error near RP sensor
Jam Error near JP sensor
Jam Error near SP sensor
Jam Error near Selector
Fixing Problems
or
1. Check if the banknote is inside.
2. Close the cover until it clicks in
place.
3. Press CLEAR.
1. Remove the banknotes.
2. Press CLEAR.
1. Remove banknotes on the Hopper.
2. Press CLEAR.
Caution:
In occurrence of JAM3, if the note is tightly jammed and it is not easy to remove it, then please
open the rear cover and turn a roller to reverse direction by hand, then the jammed note will be
clear easily.
- 15 -
CURRENCY DISCRIMINATION COUNTER
5
- 16 -
Connection Diagram
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
6
SB-9(2000S) SERVICE MANUAL
S/W Version and Currency Check
9 MENU
MODE
CODE [*****]
3
2
SERVICE MENU1
1.ERROR STOP CTRL.
2.SENSOR LEVEL
3.SYSTEM REPORT________
4.SET A/S CALL No.
5.SET MACHINE S/N
6.SHADING
7.SENSOR SELECT
SYSTEM REPORT
1. COUNTING REPORT
2. S/W VERSION______

S/W VERSION
VERSION
CHECKSUM
01.00
515E
CURRENCY SPEC
FA
SPEC 5
SOFT SPEC 5
The left image shows Version and Checksum of the software
installed in the machine.

‘FA SPEC’ means the number of currency which can be
installed on the machine and ‘SOFT SPEC’ means the
number of currency which is installed on the machine.
‘FA SPEC’ and ‘SOFT SPEC’ should be same. (Please
check this number when you upgrade the firmware or
replace the PBA Main)
- 17 -
CURRENCY DISCRIMINATION COUNTER
7
SB-9(2000S) SERVICE MANUAL
SERVICE MENU 1
There are ‘Service Menu1’ and ‘Service Menu2.’
‘Service Menu1’ includes mainly the menu for adjusting Parameter of Sensors.
7-1. How to enter ‘SERVICE MENU 1’:
Press: 9→MODE→ *****
To exit from the current function, press ‘9(menu)’ key and to move ‘SERVICE MENU2’, press
‘DISPLAY’ key.
SERVICE MENU1
1.ERROR STOP CTRL.
2.SENSOR LEVEL
3.SYSTEM REPORT
4.SET A/S CALL No.
5.SET MACHINE S/N
6.SHADING
7.SENSOR SELECT
< Display of ‘SERVICE MENU 1’>
7-2. ‘Service Menu1’
1. ERROR STOP CTRL. -------------
1) ERROR STOP ON / 2) ERROR STOP OFF
2. SENSOR LEVEL -------------------
1) DOUBLE LEVEL / 2) HOPPER LEVEL
3. SYSTEM REPORT -----------------
1) COUNTING REPORT / 2) S/W VERSION
4. SET A/S CALL No.
5. SET MACHINE S/N ----------------
1) S/N DISPLAY / 2) S/N SETTING
6. SHADING -----------------------------
1) UV SHADING / 2) MR SHADING / 3) CIS SHADING /
4) IR SHADING
7. SENSOR SELECT -----------------
- 18 -
1) UV / 2) MR / 3) IR / 4) CF DETAIL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
1. ERROR STOP CTRL.
Sometimes there is need to prevent from stopping the
ERROR STOP CTRL.
1. ERROR STOP ON
2. ERROR STOP OFF
machine even though some error is occurred when you test
the machine. If you want to do this, select “ERROR STOP
OFF”. But after the test, it must be restored to “ERROR
STOP ON”
2. SENSOR LEVEL
In this mode, you can adjust the reference levels of the
SENSOR LEVEL
1. DOUBLE LEVEL
2. HOPPER LEVEL
Hopper sensor and Double detection level. To change the
level, press UP/DOWN key and START key to save the
change then exit from the menu by pressing ‘9(menu)’ key.
 DOUBLE LEVEL: If the machine detects one note as
Double, lower the level. If the machine does not detect
Double notes, raise the level. (Default- 10)
 HOPPER LEVEL: If the machine does not detect it, even
though there are notes on the Hopper, lower the level.
(Default- 200)
3. SYSTEM REPORT
Counting Report
SYSTEM REPORT
1. COUNTING REPORT
2. S/W VERSION
In this mode, you can see the total number of the counted notes
and the rejected notes.
S/W version
You can check the version of S/W and Currency.
4. SET A/S CALL No.
After the machine is turned on, A/S call no. is displayed on LCD.
A/S
NO. SETTIMG
In this mode, you can set the telephone no. It is available up to
_
20 characters by using Numeric Key and then press START key
PRESS START TO SAVE
to save it.
UP key - Back Space
DOWN key – Used as Right key
- 19 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
5. SET MACHINE S/N
S/N Display
You can check the serial no. of the machine.
(In order that S/N is displayed correctly, S/N should be input first in
S/N Setting menu.)
SET MACHINE S/N
1. S/N DISPLAY
2. S/N SETTING
S/N Setting
You can input the serial no. of the machine. It is available up to 20
characters by using Numeric Key.
UP key - Back Space
DOWN key – Used as Right key
6. SHADING
SHADING
1. UV SHADING
2. MR SHADING
3. CIS SHADING
4. IR SHADING
In order that a system analyzes Reference Level and
a signal of the machine, the system should know the
full swing of a waveform of a signal.
What is Shading?
Shading is to make a full swing reference waveform to read the full level of a signal. If the
machine rejects too many notes, the system might not analyze the input of waveform.
It is possible to make a standard waveform for the system.
For more detail information, please refer to the Chapter9.
7. SENSOR SELECT
Sensor Select pass word: *****
ENTER CODE
[
]
UV, MR, IR: If you want to turn on or off some kind of sensor,
you can do that in this mode.
SENSOR SELECT
1. UV
2. MR
3. IR
4. CF DETAIL
ON
ON
ON
OFF
CF Detail: In case that the machine would reject a Counterfeit
note, you can check the detail reject reason using this menu.
(Turn on this menu and select ‘Reject Reason view’)
Select menu by using UP/DOWN and change ON/OFF by
using START key.
- 20 -
CURRENCY DISCRIMINATION COUNTER
8
SB-9(2000S) SERVICE MANUAL
SERVICE MENU 2
There are ‘Service Menu1’ and ‘Service Men2’ in Service Menu.
‘Service Menu2’ includes the menu to have a test for development or for repair.
8-1. How to enter ‘SERVICE MENU 2’:
Press: 9→MODE→ ***** →DISPLAY
To exit from the current function, press ‘9(menu)’ key.
To move ‘SERVICE MENU1’, press ‘MODE’ key.
SERVICE MENU2
1. SENSOR TEST
2. KEY TEST
3. MOTOR TEST
4. SELECTOR TEST
5. WING SPEED SETTING
< Display of ‘SERVICE MENU2’>
8-2. ‘Service Menu2’
1. SENSOR TEST ------------------------
1) LED TEST
A. HOPPER LED ON
B. HOPPER LED OFF
C. SENSOR LED ON
D. SENSOR LED OFF
2) HOPPER TEST
3) SENSOR LOGIC TEST
4) DOUBLE LOGIC TEST
2. KEY TEST
3. MOTOR TEST --------------------------
1) DRIVING TEST / 2) DRIVING TEST(P-OCR)
3) FEEDING TEST
4. SELECTOR TEST---------------------
1) SELECTOR STACKER / 2) SELECTOR REJECTOR
5. WING SPEED SETTING-------------
1) WING 1000NPM / 2) WING 1200NPM / 3) WING 1500NPM
- 21 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
1. SENSOR TEST
SENSOR TEST
1. LED TEST
2. HOPPER TEST
3. SENSOR LOGIC TEST
4. DOUBLE LOGIC TEST
1) LED TEST
Turn ON/OFF LED. (IR sensors are not visible, i.e. hopper, RP1
…)
2) HOPPER TEST
In this mode, the level of HOPPER is displayed
Please refer to Page 40.
3) SENSOR LOGIC TEST
In this mode, you can check if the sensor is defective or not by checking detected logic status of each sensor. The
below pictures shows logic status when the sensor is covered or open by note.
CASE
All doors are closed.
LCD DISPLAY
PICTURE
RP1
LEFT
0
RIGHT
0
JP
SP
FRONT
0
0
0
0
0
REAR 0 0
REJECT F
STACKER
0
0
R
0
Front Door is open.
RP1
LEFT
1
RIGHT
1
JP
SP
FRONT
1
0
1
1
0
REAR 0 0
REJECT F
STACKER
0
0
R
0
Rear Door is open.
RP1
LEFT
0
RIGHT
0
JP
SP
FRONT
0
1
0
0
1
REAR 0 1
REJECT F
STACKER
0
0
R
RP1
LEFT
1
JP
SP
FRONT
REJECT F
STACKER
1
1
1
0
0
0
Front and Rear Door are
open.
- 22 -
RIGHT
1
1
1
REAR 0 1
R
0
CURRENCY DISCRIMINATION COUNTER
CASE
SB-9(2000S) SERVICE MANUAL
LCD DISPLAY
PICTURE
Reject F
(Front) sensor is
RP1
LEFT
0
covered.
JP
SP
FRONT
REJECT F
STACKER
0
0
0
1
0
(Rear) sensor is
RP1
LEFT
0
covered.
JP
SP
FRONT
REJECT F
STACKER
0
0
0
0
0
RIGHT
0
0
0
REAR 0 0
R
0
Reject R
RIGHT
0
0
0
REAR 0 0
R
1
Stacker sensor is
covered.
RP1
LEFT
0
JP
SP
FRONT
REJECT F
STACKER
0
0
0
0
1
RIGHT
0
0
0
REAR 0 0
R
0
4) DOUBLE LOGIC TEST
With this mode, you can check the double level.
DOUBLE TEST
CH LEFT :
CH RIGHT :
700
700
Before you select this mode, you need to check bellows.

Clean the all notes in the path and close all doors.

Please run the motor more than 5 sec.
Both of double level(Channel left and right) needs to adjusted ‘700’ (± 50).
For more detail information, please refer to the Chapter10.
- 23 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
2. KEY TEST
In this mode, you can have a test if the machine detects the
input of key. Every time you press a key, the name of the key
will be displayed on LCD. However, in case of CLEAR key,
you exit from the current menu in stead of displaying.
PRESS ANY KEY
After you push the “start” button, and press 9(menu) key, you
can exit from the current menu.
3. MOTOR TEST
MOTOR TEST
1. DRIVING TEST
2. DRIVING TEST (POCR)
3. FEEDING TEST
1) Driving Test
You can run Main and Feed Motor in various speeds.
2) Driving Test (POCR)
You can run Main and Feed Motor in low speed.
3) Feeding Test
You can input notes (More than 5 notes) and test the speed
of each level. (Speed: LOW, 1000, 1200, 1500 NPM)
4. SELECTOR TEST
SELECTOR TEST
1. SELECTOR STACKER
2. SELECTOR REJECTOR
1) Selector Stacker
RED LED on the right of Front OPE lights and Selector sends the
notes to stacker.
2) Selector Rejecter
RED LED on the right of Front OPE is turned off and Selector
sends the notes to Rejecter.
5. WING SPEED SETTING
WING SPEED SETTING
1. WING 1000NPM
2. WING 1200NPM
3. WING 1500NPM
The speed of Wing Stacker can change fast or slow (“±10”) by
pressing UP/DOWN key and press “START: key to save it.
To exit from current menu, press 9(menu) key.
- 24 -
CURRENCY DISCRIMINATION COUNTER
9
SB-9(2000S) SERVICE MANUAL
Shading
What is Shading?
Shading is to make a full swing reference waveform to read the full level of a signal. If the
machine rejects too many notes in Mixed Mode or in CF Detection Mode, the system
might not analyze the input of waveform. It is possible to make a standard waveform for
the system.
SHADING
1. UV SHADING
2. MR SHADING
3. CIS SHADING
4. IR SHADING
< Display of SHADING MENU >
There are 4 kind of shading as the above image. .
UV SHADING, MR SHADING, CIS SHADING and IR SHADING.
The below steps are necessary before doing shading.
1. Load default parameter. (Press : 9(menu) → 7→ 1 → C(Clear)
2. Clean UV, MR, CIS and IR Sensor.
- 25 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
9-1. UV SHADING
<UV SHADING SHEET : SHINWOO UV SHADING V1.0>
165 mm
75 mm
Shading sheet provided from SBM should be used.
Shading sheet provided from SBM should be used.
Before UV shading, put UV shading sheet inside Front cover as the below image.
Open Front Cover and brush the dust.
Place UV SHADING SHEET in the
middle of Hopper like the picture.
Close Front Cover.
- 26 -
CURRENCY DISCRIMINATION COUNTER
9 MENU
SB-9(2000S) SERVICE MANUAL
MODE
1
CODE [ ***** ]
6
SHADING
1. UV SHADING__________
2. MR SHADING
3. CIS SHADING
4. IR SHADING
Wait.
SERVICE MENU1
1. ERROR STOP CTRL.
2 .SENSOR LEVEL
3. SYSTEM REPORT
4. SET A/S CALL No.
5. SET MACHINE S/N
6. SHADING_______________
7. SENSOR SELECT
Shading sheet is pushed out.
UV SHADING
WAIT . . ABOUT 5 SEC
If ‘▼’ is pressed, the detail on shading of each
currency is displayed.
To skip, press ‘9’.
▼
UV SHADING – USD
175 130 95 54
51
51
UV
(OK - 670)
670
SUVT (OK - 500)
497
UVR (OK - 300)
301
If shading of each currency is
done normally,
OK is displayed.
UV SHADING
USD
OK
EUR
OK
(▼ KEY TO SEE NEXT)
(▼ KEY TO SEE NEXT)
After check shading result, press clear button.
If you want to move previous Level, press ‘9’.
- 27 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
9-2. MR SHADING
<MR SHADING SHEET :USA ONE DOLLAR Real Banknote>
Needed Quantity of MR SHADING SHEET
1 ~ 5 pcs
9 MENU
2
SHADING
1. UV SHADING
2. MR SHADING__________
3. CIS SHADING
4. IR SHADING
- 28 -
MODE
CODE [*****]
6
SERVICE MENU1
1. ERROR STOP CTRL.
2 .SENSOR LEVEL
3. SYSTEM REPORT
4. SET A/S CALL No.
5. SET MACHINE S/N
6. SHADING_______________
7. SENSOR SELECT
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Place 1~5 pcs of Sheet on the
Hopper.
Place the sheets in the middle of the
Hopper like the picture.
MR SHADING
PLACE SHADING PAPER
ON HOPPER
Check
if ‘OK’ is displayed.
The note is sent to Stacker.
MR SHADING
OK
Norm: 0.84
Noise:
3
2
1
2
1
2
L:1 R:2
Level: 294(High) (5)
33 31
55 51 42
38 L:46 R:37
It is better if the value of Noise is lower. When you consider that the value of Noise is the
Minimum after doing MR shading about five times, stop doing MR shading.
Reference on MR SHADING ‘NG’
1) Noise : If average value is more than ’10’, it is ‘NG’
2) Level : If average value is less than ’10’, it is ‘NG’
MR SHADING
NG
Norm: 1.56
Noise:
3
2
1
2
12
2
L:1 R:2
Level: 547(High) (5)
55 66 98 98 92
94
L:46 R:26
C
MRA Sensor
MR Single Sensor
After check shading result, press clear button.
or
9 MENU
If you want to move previous Menu, press ‘9’.
- 29 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
MR SHADING and MDD(Module Double Detector) SHADING are performed simultaneously. As a
figure below, MR SENSOR is O.K. in NOISE and LEVEL. But in case NG REASON displays NG(0),
MDD is not good.
Module Double Detector NG
MR SHADING
NG(0)
Norm: 1.56
Noise:
3
2
1
2
12
2
L:1 R:2
Level: 547(High) (5)
55 66 98 98 92
94
L:46 R:26
In case NG(0), please refer to page
XX and check the MDD sensor.
Do not place MR SHADING SHEET on the hopper like the below images.
Wrong Direction
- 30 -
Lean to the right
Skew
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
9-3. CIS SHADING
If ‘MAIN PCB’ is replaced with a new one or there are lots of rejected notes from failure of recognition
(NO I.D), it is recommended to make a new CIS Shading.
1. Open upper cover then clean the sensors.
2. Place the shading sheet on the surface of the CIS referring to the picture.
3. Close the upper cover. Start CIS shading process.
CIS Shading Sheet
- 31 -
CURRENCY DISCRIMINATION COUNTER
9 MENU
SB-9(2000S) SERVICE MANUAL
CODE [*****]
MODE
6
3
SERVICE MENU1
1. ERROR STOP CTRL.
2 .SENSOR LEVEL
3. SYSTEM REPORT
4. SET A/S CALL No.
5. SET MACHINE S/N
6. SHADING_______________
7. SENSOR SELECT
SHADING
1. UV SHADING
2. MR SHADING
3. CIS SHADING
4. IR SHADING
Please wait approximately 5
Check if ‘OK’ is displayed.
seconds.
CIS SHADING
WAIT . . ABOUT 5 SEC
CIS SHADING
MIN MAX AVG UNI
B 0.00 0.71 0.00 –
W 0.78 1.11 0.98 87%
OnTime1 :
R=80 / G=111 / B=83
OnTime2 :
R=42 / G=57 / B=43
OK
▼
or
9 MENU
After checking shading result,
press ‘▼’ button.
If you want to move previous
Menu, press ‘9’.
- 32 -
▼
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
9-4. IR SHADING
<IR SHADING SHEET (WHITE): SBM IR SHADING V3.0 White>
202 mm
145 mm
62 mm
70 mm
This side faces upward
This side faces downward
Shading sheet provided from SBM should be used
Prepare to have IR SHADING WHITE
Open Front Cover and
brush the dust.
Place IR SHADING SHEET
in the middle of Hopper
like the picture.
Close Front Cover
After prepare IR SHADING, refer to the below and have IR shading
- 33 -
CURRENCY DISCRIMINATION COUNTER
9 MENU
SB-9(2000S) SERVICE MANUAL
CODE [ ***** ]
MODE
4
6
SERVICE MENU1
1. ERROR STOP CTRL.
2 .SENSOR LEVEL
3. SYSTEM REPORT
4. SET A/S CALL No.
5. SET MACHINE S/N
6. SHADING_______________
7. SENSOR SELECT
SHADING
1. UV SHADING
2. MR SHADING
3. CIS SHADING
4. IR SHADING__________
▼
Wait.
IR SHADING
MIN MAX AVG UNI
IB 0.00 0.74 0.00
–
IW 0.87 1.28 1.00 82%
IR SHADING
WAIT . . ABOUT 5 SEC
WB 0.00 0.74
WW 0.88 1.14
0.00 –
0.99 90%
OnTime1: IR_T = 57
OnTime2: WHT T = 63
OK
Check if the result is ‘OK’
If ‘▼’
pressed, shading value is displayed.
To skip, press ‘9’.
▼
This shows WHITE LEVEL.
▼
- 34 -
or
After checking shading result, press ‘▼’ button.
9 MENU
If you want to move previous MENU, press ‘9’.
is
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
9-5. ERROR
1) UV SHADING ‘NG’
UV SHADING
USD
EUR
NG
OK
(▼ KEY TO SEE NEXT)
Check if shading sheet is clean and there is no problem with the
sheet.
Then, have shading according the order.
2) NO UV SHADING SHEET
NO UV SHADING SHEET
If a shading sheet is not inserted, this message may be
displayed. Refer to the process and do shading.
MR SHADING
NG(27)
Norm: 1.39
Noise:
2 4 4 3 3
2
L:23 R:2
Level: 486(High) (5)
65 71 77 96 95
84 L:44 R:22
Check if have a shading normally. If do orderly but NG is
displayed, sensor might have a problem.
4) MR ERROR
MR TEST
If motor runs without SHADING SHEET, this message is displayed.
Place shading sheet on Hopper and have shading.
ERROR
IR SHADING
MIN MAX
IB 0.00 0.74
IW 0.56 1.16
WB 0.00 0.74
WW 0.62 1.11
3) MR SHADING ‘NG’
5) IR SHAIDNG ‘NG’
AVG UNI
0.00
–
1.00 56%
0.00 –
0.42 66%
Check if proper shading sheet is placed and shading sheet is clean.
After that, have shading in order.
OnTime1: IR_T = 18
OnTime2: WHT T = 9
NG
IR SHADING
MIN MAX
IB 0.00 0.74
IW 0.87 1.16
WB 0.00 0.74
WW 0.36 0.54
6) NO IR SHADING SHEET
AVG UNI
0.00
–
1.00 82%
0.00 –
0.42 89%
If a shading sheet is not inserted, this message might be
displayed. Refer to the process and do shading.
OnTime1: IR_T = 18
OnTime2: WHT T = 9
NG NoSheet
- 35 -
CURRENCY DISCRIMINATION COUNTER
10
SB-9(2000S) SERVICE MANUAL
Adjustment
10-1. Gap of ADF
CAUTION
Turn off the machine before adjustment.
If too Wide  ‘Double Feeding’ or ‘Over Run’
If too Narrow  ‘Miss Feeding’ or ‘Jam0’
Check Gap of ADF by using one
Check Gap of ADF by using 2 pcs
note. Check both sides and Gap of
of notes. If 2 pcs of notes are fed,
both sides should be equal.
adjust Gap so only one note can be
fed.
-. The gap should not be too wide to get overlapped 2 number of banknote input into it.
-. Adjust gap for tightly go in and easily out.
Tighten
Loosed
(Narrower)
(Wider)
Loosed (Wider)
Tighten (Narrower)
- 36 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
10-2. ADF & Pickup Roller Timing
CAUTION
Turn off the machine before adjustment.
4 Tooth ± 1
0 Tooth
PICK_UP_ROLLER-P
ADF_ROLLER-P
Loosen the belt and then adjust the timing.
Fit the belt on pulley.
If the timing is not adjusted properly, the problem such as NO ID, OVER RUN and so on
could happen.
10-3. Guide Selector
If the notes are damaged as Jam3 often happens, Selector may be not properly adjusted.
.
Step 1. Loosen SCREW slightly.
- 37 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Step 2. Open Rear Door. Put your hand inside of the machine and lift up Guide SELECTOR as the below
image. (In this case, notes are sent to Stacker.)
Step 3. Be careful with the tip of Selector Guide so that notes are not jammed in the Selector while the notes
are transferred. (The image on the left among the below image is an example showing wrong
adjustment of Guide Selector. In this case, notes would be jammed in the Selector. )
0.5 mm
( O )
( X )
Step 3. Tighten SCREW (A) as the image on the left side.
B
C
At this time, the axis (‘C’) of SOLENOID should be
placed in the center of the hole (‘B’) in BKT
SELECTOR.
A
Step 4. After adjustment is done, check if Solenoid normally works in ‘Selector Test ‘ Mode.
( Press : ‘9’→’MODE’→ ‘*****’ →’DISPLAY’ →’4’)
- 38 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
10-4. Brightness of LCD (Back Light)
Step 1. . Remove Side Cover.
Step 2. Pull OPE cover slightly to
remove OPE cover as the below
image.
Step 3. Maintain the space as the below image so
that you can adjust it comfortably.
Step 4. Turn on the machine.
Be careful with the operation of motor as Hopper
sensor is working.
- 39 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Step 5. Adjust brightness referring to the below image.
Adjust R16 (Variable Resistor) with Driver checking LCD Back Light.
High
Low
R16
10-5. Hopper sensitivity
Step 1. Hopper Test Mode
(Press : ‘9’→’MODE’→ ‘ ***** ’→’DISPLAY’→ ‘1.SENSOR TEST’→’2.HOPPER TEST’)
1
SERVICE MENU2
1. SENSOR TEST____
2. KEY TEST
3. MOTOR TEST
4. SELECTOR TEST
5. WING SPEED SETTING
2
SENSOR TEST
1. LED TEST
2. HOPPER TEST
3. SENSOR LOGIC TEST
4. IR LOGIC TEST
5. IRA TEST
Step 2. Make Sheet for Hopper Test.
Attach printed black sheet to the paper that its width is smaller
than 52mm.
Refer to the image on the right. (It is OK, if matte insulating
tape to kind of business card.)
Step 3.
Place the Sheet on the Hopper sensor.
Check if the black tape cover Hopper sensor. The sheet should not reach both rollers.
- 40 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Step 4. Adjust R9 (Variable Resistor) so that DIFFERENCE can be from 190 to 210.
HOPPER ON :
HOPPER OFF. :
213
13
DIFFERENCE .:
200
High
Low
R9
10-6. Reject Pocket Sensor Level
If LED lights even though there are no notes on the REJECT POCKET or if LED does not light
even though there are notes on the REJECT POCKET, adjust sensitivity of REJECT
SENSOR.
10-6-1. Reject Sensor
Reject F (Front Sensor)
Reject R (Rear Sensor)
- 41 -
CURRENCY DISCRIMINATION COUNTER
10-6-2. Test Point and adjust Point
SB-9(2000S) SERVICE MANUAL
Adjust point: Reject F
High
Low
Test Point 3 : Reject F
High
Low
Test Point 4 : Reject R
Adjust Point: Reject R
200 mm
80 ~ 82mm
Step 1. How to make sheet for adjusting ‘Reject F’
Make a test sheet for adjustment with ‘IR SHADING
(DARK) Sheet’ Provided by SBM.
Cut dotted part as the image on the left side.
Step 2. Place the cut sheet on the REJECT POCKET.
At this time, black side should face upward.
- 42 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Step 3. Adjustment of ‘Reject F’
Adjust R97 (Variable Register) so that the voltage of TP3 (Test Point 3) can be 3.2V.
Step 4. Adjustment of ‘Reject R’
Adjust R35 (Variable Register) so that the voltage of TP4 (Test Point 4) can be 1.2V.
10-7. Double Sensor Level
DOUBLE LOGIC TEST
With this mode, you can check the double level.
DOUBLE TEST
CH LEFT :
CH RIGHT :
751
750
Before you select this mode, you need to check bellows.

Clean the all notes in the path and close all doors.

Please run the motor more than 5 sec.
You need to set the double level to ‘700’ (± 50) using variable resister ‘R123’ and ‘R128’ located in PBA Main.
(Please refer to below fig.)
- 43 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Press ‘Menu’  ‘Mode’  ‘55757’  ‘1.Sensor Test’  ‘4. Double logic test’.
Please adjust ‘Channel Left’ using ‘R123’ and adjust ‘Channel Right’ using ‘R128’. Both of target levels are ‘700’ (±
50).
- 44 -
CURRENCY DISCRIMINATION COUNTER
11
SB-9(2000S) SERVICE MANUAL
Program Upgrade
11-1. Program Upgrade
Save Upgrade File (.sb9) provided by SBM in USB flash drive.
Save only .sb9 file, not to save the folder.
▲
Wait for a while.
Turn on the machine
PLEASE
INSERT
U S B
BOOT VN
KERNEL
LOADING
pressing the button.
Insert USB into USB port
▲
▼
Select
the
software
pressing the button.
▶1. 05_RUR_USD_EUR(V1.0
2. 08_KRW_USD_EUR_JPY
by
START
Press “START” key.
ENTER/STOP
1. 05_RUR_USD_EUR(V1.0
▶2. 03_KRW_USD_EUR_JPY
- 45 -
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
Check version and checksum of the software and press “START” Key.
1. 01_USD(V1.00_5032)
START
03_KRW_USD_EUR_JPY
_CNY(V1.02_515E)E5AAT
[IW]_090820.sb9
ENTER/STOP
If the software is not the software for
upgrade, press “C” key to move back
to the previous step.
C
Upgrading..
PROGRAM
LOADING OK
WRITING
The
machine
automatically
reboot after the upgrade is
Do not take out USB during
upgrading.
Check version and checksum after the
machine reboots and take out USB.
done.
VERSION 01. 02
PROGRAM
LOADING OK
WRITING
OK
CHECKSUM OK
515E
A/S NO.
123 456
If it is difficult to check Version and
Checksum, refer to Chapter 6.
- 46 -
CURRENCY DISCRIMINATION COUNTER
12
SB-9(2000S) SERVICE MANUAL
Assembly Drawings
INDEX
Cover Exp View
Ass'y Exp View
Frame Exp View
Roller Exp View
Cover Door Top
Cover Door Top Upper
Housing Pocket
Ass'y Ope.
Plate Side R
Plate Side L
Base Exp View
Bkt Stacker Sensor
Cover Top
Shaft Case Detector
Case Detector with MR
Double Sensor
Plate Reinforce
Plate Guide Upper
Plate Guide Lower
Exp Guide Lower-P
Bkt SMPS Bottom
Bkt SMPS Top
- 47 -
CURRENCY DISCRIMINATION COUNTER
13-1. Cover Exp View
- 48 -
1
COVER_RIGHT
2
SCREW_M/C_PWH_M3X6_Fe_Ni
3
COVER_SMPS
4
SCREW_M/C_FH_M3X8_Fe_Ni
5
ASS'Y_COVER_DOOR_TOP
6
COVER_SPECIAL_SCREW
7
SCREW_T/P_FH_M3X10_Fe_Zy
8
COVER_LEFT
9
ASS'Y_OPE
10
ASS'Y_HOUSING_POCKET
11
SCREW_T/P_PH_T2_Ø3X8_Fe_Ni
12
CAP_STACKER_SENSOR
13
GUIDE_STACKER
14
ASS'Y_REJECT_PLATE
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-2. Ass'y Exp View
1
SCREW_M/C_PH/SWW_M4X8_Fe_Ni
2
PIVOT_HINGE_LOWER
3
ASS'Y_GUIDE_LOWER
4
LINK_COVER_REAR_L
5
COVER_REAR
6
E_RING_Ø4(4x11x0.6)_Fe_ZB
7
LINK_COVER_REAR_R
8
SHAFT_COVER_REAR
9
E_RING_Ø6(6x12x0.8)_Fe_ZB
10
SHAFT_COVER_TOP
11
BUSH_HINGE
12
ASSY'_PLATE_GUIDE_UPPER_P
13
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
14
ASS'Y_PLATE_GUIDE_LOWER_P
15
SCREW_M/C_PH/SWW_M4X8_Fe_Ni
16
P-MAIN
17
P-AMP
18
P-POWER_IO
19
ASS'Y_PLATE_REINFORCE
20
ASS'Y_COVER_TOP
21
SCREW_M/C_PWH_M3X6_Fe_Ni
- 49 -
CURRENCY DISCRIMINATION COUNTER
13-3. Frame Exp View
- 50 -
1
ASS'Y_BKT_SMPS_BOTTOM
2
SCREW_M/C_FH_M3X8_Fe_Ni
3
ASS'Y_BKT_SMPS_TOP
4
ASS'Y_PLATE_SIDE_L
5
SUPPORT_PCB
6
SCREW_M/C_PH/SWW_M4X8_Fe_Ni
7
ASS'Y_WING_STACKER_SENSOR
8
ASS'Y_PLATE_BASE_P
9
ASS'Y_PLATE_SIDE_R
10
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-4. Roller Exp View
1
BELT_FEEDER (S3M228)
18
BUSH_SELECTOR
2
E_RING_Ø6(6x12x0.8)_Fe_ZB
19
ASS'Y_SWING_SELECTOR
3
PULLEY_FEED
20
SCREW_M/C_PH_M3X8_Fe_Zy
4
BEARING_LF_1680ZZ
21
PIPE_SELECTOR_CONN
5
ROLLER_FEED_2_P
22
SOLENOID (KHA38H06A) (W/ SHP-19 Harness)
6
ROLLER_FEED_1_P
23
BKT_SELECTOR_P
7
ENCODER_WHEEL
24
MOTOR_SHIELD
8
SCREW_M/C_PH/SWW_M4X8_Fe_Ni
25
ASS'Y_MOTOR_FEED_P (W/ Pulley and Harness)
9
COVER_ENCODER_WHEEL
26
ASS'Y_MOTOR_MAIN_P (W/ Pulley and Harness)
10
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
27
PIVOT_SUPPORT_REAR
11
ROLLER_FEED_MR_P
28
PULLEY_ADF_P
12
BELT_ ADF (S3M189)
13
ROLLER_ADF_P (W/ WAVE_WASHER_GUIDE) 29
ROLLER_PICK_UP_P
30
14
PBA_ENCODER_2 (W/ SHP-01 Harness + 2 PBA)31
ASS'Y_PULLEY_ADF_CLUTCH (W/ BEARING)
15
PBA_ENCODER_1 (W/ SHP-27 Harness)
32
BELT_ADF_FEEDER (S2M160)
16
LINK_SELECTOR
33
PULLEY_FEED_CLUTCH
17
E_RING_Ø6(6x12x0.8)_Fe_ZB
PLASTIC_WASHER_Ø8(8.2x13x_0.25T)
- 51 -
CURRENCY DISCRIMINATION COUNTER
13-5. Cover Door Top
1
COVER_DOOR_TOP_UPPER
2
COVER_DOOR_TOP_LOWER
3
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
13-6. Cover Door Top Upper
- 52 -
1
COVER_DOOR_TOP_UPPER
2
HOPPER_GUIDE_L
3
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
4
RACK_L
5
GEAR_BILL_GUIDE_P
6
GUIDE_RACK
7
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
8
RACK_R
9
HOPPER_GUIDE_R
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-7. Housing Pocket
1
HOUSING_POCKET
2
PIN_REJECT_BAR
3
SPRING_LIMIT_REJECT
4
LIMIT_REJECT
5
SCREW_T/P_FH_M3X8_Fe_Ni
6
PORON_LIMIT_REJECT
7
REJECT_PLATE
8
ELECTRO_BRUSH
9
BKT_E_BRUSH
10
TAPE_E_BRUSH
- 53 -
CURRENCY DISCRIMINATION COUNTER
13-8. Ass'y OP PANEL
- 54 -
1
WINDOW_LCD_P (W/Tape)
2
COVER_OP_PANEL
3
ELECTRO_FORMING_BADGE
4
LCD(ODT_TECH 128X80) (W/ 2P Harness)
5
BUTTON_NUMERIC_P
6
LENS_LED
7
DOME_SHEET_NUMERIC
8
BUTTON_FUNCTION_P
9
DOME_SHEET_FUNCTION
10
P-OPE
11
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
12
QUICK_CLAMP_DQC_106
13
HEX_NUT_M3X0.5_Fe_Zy
14
PBA_HOPPER_1 (W/ SHP-22 Harness)
15
WINDOW_HOPPER
16
SCREW_M/C_FH_M3X12_Fe_Ni
17
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-9. Plate Side R
1
PLATE_SIDE_R
2
TORSION_SPRING_OPEN_HOOK_R_P
3
OPEN_HOOK_R_P
4
E_RING_Ø6(6x12x0.8)_Fe_ZB
5
COVER_SADDLE_DS-2
6
WIRE_SADDLE_SMALL
- 55 -
CURRENCY DISCRIMINATION COUNTER
13-10. Plate Side L
- 56 -
1
PLATE_SIDE_L
2
TORSION_SPRING_OPEN_HOOK_L_P
3
OPEN_HOOK_L_P
4
E_RING_Ø6(6x12x0.8)_Fe_ZB
5
SUPPORT_PCB
6
SIDE_LOCKING_SADDLE_DS-110
7
SIDE_LOCKING_SADDLE_DS-111A
8
COVER_SADDLE_DS-2
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-11. Base Exp View
1
PLATE_BASE_P
2
FOOT_MOLD
3
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
4
RUBBER_FOOT_P
5
WIRE_SADDLE_SMALL
- 57 -
CURRENCY DISCRIMINATION COUNTER
13-12. Bkt Stacker Sensor
- 58 -
1
MOTOR_STACKER (W/ SHP-18 Harness)
2
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
3
BUSH_STACKER_MOTOR_P
4
WING_STACKER_P
5
SHAFT_STACKER_P
6
BUSH_STACKER_WING
7
BKT_STACKER_SENSOR_P
8
WIRE_SADDLE_SMALL
9
P-STACKER_TRN_V1.2 (W/ 2P Harness)
10
CAP_UV
11
P-STACKER_RCV_V1.2 (W/ 2P Harness)
12
SNAP_RIVET_(SR2664B)
13
GROUND_FINGER
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-13. Cover Top
1
ASS'Y_CASE_DETECTOR
2
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
3
E_RING_Ø5(5x11x0.6)_Fe_ZB
4
BUSH _HINGE
5
BKT_COVER_TOP
6
ARM_ADJUST_UPPER
7
COIL_SPRING_ADJUST
8
SPECIAL_SCREW_ADUSJT
9
SCREW_M/C_PH/SWW_M3X8_Fe_Zy
10
COVER_SADDLE_DS-2
11
ASS'Y_BKT_SEPARATOR_P
- 59 -
CURRENCY DISCRIMINATION COUNTER
13-14. Shaft Case Detector
- 60 -
1
ASS'Y_GUIDE_PRESS_ROLLER_P
2
ROLLER_SEPARATOR_P
3
ASS'Y_BUSH_ONEWAY_BEARING_P
4
E_RING_Ø7(7x14x0.8)_Fe_ZB
5
BKT_SEPARATOR_P
6
SHAFT_CASE_DETECTOR
7
SCREW_M/C_PH/SWW_M4X10_Fe_Ni
8
HEX_NUT_M4X0.7_Fe_Zy
9
SCREW_SET_SIH_FP_M4x6_Fe_ZB
10
SCREW_M/C_PH/SWW_M4X20_Fe_Ni
11
ARM_ADJUST_LOWER
12
TORSION_SPRING_ADJUST
13
E_RING_Ø6(6x12x0.8)_Fe_ZB
14
BEARING_LF_1680ZZ
15
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
16
ASS'Y_GUIDE_TRANSFER_ROLLER_P
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-15. Case Detector With MR
1
UV_FILTER(N) (420nm, D7*2.5T)
9
MRA
2
SUV_FILTER (375nm, D7*2.5T)
10
MRS_R
3
GLASS_UV_REFLECT
11
MRS_L
4
CASE_DETECTOR_P2
12
RP_RCV
5
CAP_RP
13
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
6
PBA_IR_TRN_MODULE
14
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
7
LOCKER_IR_LED
8
MDD (Module Double Detector)
- 61 -
CURRENCY DISCRIMINATION COUNTER
13-16. Double Sensor
- 62 -
1
DOUBLE_BRACKET_BASE
2
DOUBLE_BRACKET_ROLLER
3
BEARING L_1560ZZ
4
SHAFT_DOUBLE
5
DOUBLE_PLATE_DUST
6
7
SPRING_DOUBLE
DOUBLE_SENSOR
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-17. Plate Reinforce
1
REJECT_BAR
2
PLATE_REINFORCE
3
GUIDE_RPS
4
PBA_REJECT_T
5
WINDOW_HOPPER
6
PBA_REJECT_R
7
SCREW_M/C_PH/SWW_M3X8_Fe_Zy
8
SCREW_M/C_PH/SW_M3X6_Fe_Zy
9
QUICK_CLAMP_DQC_103
- 63 -
CURRENCY DISCRIMINATION COUNTER
13-18. Plate Guide Upper
- 64 -
1
PLATE_GUIDE_UPPER_P2
2
COVER_SENSOR_P2
3
JP_TRN
4
GUIDE_RPS
5
PBA_JP/SP_T
6
CIS(SB9)
7
BKT_CIS_P2
8
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
9
SCREW_M/C_PH_M3X8_Fe_Zy
10
SCREW_M/C_PH/SWW_M3X8_Fe_Zy
11
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-19. Plate Guide Lower
1
PLATE_GUIDE_LOWER_P
2
COVER_SENSOR
3
P-JPSP_RCV
4
SCREW_M/C_PH_M3X8_Fe_Zy
5
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
- 65 -
CURRENCY DISCRIMINATION COUNTER
13-20. Exp Guide Lower-P
- 66 -
1
SCREW_T/P_PH_T2_Ø3X8_Fe_Zy
2
GUIDE_PINCH_ROLLER
3
TORSION_SPRING_PINCH
4
ASS'Y_SHAFT_PINCH
5
GUIDE_LOWER
6
P-SP_TRN
7
8
COVER_SENSOR
ASS'Y_SHAFT_PINCH_EXIT
9
SCREW_T/P_PH_T2_Ø3X6_Fe_Zy
SB-9(2000S) SERVICE MANUAL
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
13-21. Bkt SMPS Bottom
1
BKT_SMPS_BOTTOM
2,3
SHP-23 3P (AC INLET)
4
SCREW_T/P_FH_M4x10_Fe_Ni
5
COOLING_PAN_40X40(t=10mm) SHP-24 2P (IF-FAN)
6
SB-9-IF V1.5
7
NHP-02 12P (MAIN - IF)
8
NHP-03 06P (MAIN - IF)
9
SHP-25 (IF-GROUND)
10
SCREW_M/C_PWH_M3X6_Fe_Ni
11
SHP-29 (IF-SASH)
12
SHP-07 12P-10P (SMPS-POWER)
13
SCREW_M/C_PH/SWW_M3X6_Fe_Zy
14
SB-9 SMPS
15
FLIM_SMPS_P
- 67 -
CURRENCY DISCRIMINATION COUNTER
13-22. Bkt SMPS Top
- 68 -
1
BKT_SMPS_TOP
2
CUSHION_SUPPRESS_NOISE
3
COVER_SADDLE_DS-2
SB-9(2000S) SERVICE MANUAL
UV SHADING
USD
NG
EUR
OK
CURRENCY DISCRIMINATION COUNTER
SB-9(2000S) SERVICE MANUAL
(▼ KEY TO
13
Specifications
Item
Unit
Specification
Size (W x D x H)
mm
280 x 269 x 261
Weight (Net)
Kg / lbs
Approx. 9 / 20
Hopper capacity
Notes
Max. 500
Stacker capacity
Notes
Max. 200
Reject pocket capacity
Notes
Max.
Display Type
Dot
50
128 x 80
2 RS232C Port, 2 USB Port,
Connectivity interfaces
Optional:1 RJ 45 Port
Currencies available
1 (Available up to 7 currencies)
Banknote size range
mm
W: 100 ~ 185, H: 60 ~ 90
Banknote thickness
mm
0.08 ~ 0.12
Counting Speed
Notes/min
1000/1200/1500
Operating Mode
MIXED/SINGL/FACE/ORIENT/COUNT
Optional: SRL/S-OCR/P-OCR
Preset Batch Number
1 – 200
Counterfeit Detector
UV, MG, MR-Array, IR, MDD
Power Requirements
100-240VAC, 50~60Hz
Power Consumption
Ambient Conditions
W
Standby: 8 , Operation: 55
0~40deg/30~85%RH (Non Condensing)
Notes:
-
This specification can be changed without further notice to improve its reliability, function or design.
-
The contents of this user's guide can also be changed.
The height dimension does not include the height of the rubber foot.
- 69 -
Скачать