CK22 cabin

1. Packing List
INSTALLATION
INSTRUCTION
FOR CK20(H)S / CK22(H)
CABIN
A CABIN ASS’Y
NO.
2
1
1
3
1
1
1. Packing List
Part No.
Description
CABIN ASSEMBLY
Q'TY
Remarks
1
2
T2391-33121
CABIN SUPPORT(LH)
1
3
T2391-33131
CABIN SUPPORT(RH)
1
4
T2391-33251
CABIN SUPPORT SPACER
2
5
T2391-87051
HEATER HOSE D
2
6
T4340-38241
HOSE CLAMP
4
7
T2131-69351
WIRE HARNESS
(ALTERNATOR)
1
8
T2391-69361
WIRE HARNESS
(TURN SIGNAL LAMP)
2
CK20S/CK20HS
only
9
T2391-69371
WIRE HARNESS
(TURN SIGNAL LAMP)
2
CK22/CK22H
only
10
T2391-85131
CAB. FRONT SEALING
PLATE(LH)
1
10-1
01754-50620
FLANGE BOLT(M6X20L)
2
10-2
02751-50060
FLANGE NUT
2
2. general safety infoRmation
3. how to install THE cabin
4. OPERATION INSTRUCTION
Daedong kit#.(USA)
T2395-A8011 CABIN ASS’Y(CK20S)
t2396-A8011 CABIN ASS’Y(CK20HS)
T2391-80111 INTERIOR MATERIALS(CK20S)
T2392-80111 INTERIOR MATERIALS(CK20HS)
T2391-01111 SPARE KIT(CK20S/CK20HS)
4
1
5
1
6
1
7
1
Daedong kit#.(EU)
T2391-A8011 CABIN ASS’Y(CK22)
T2392-A8011 CABIN ASS’Y(CK22H)
T2391-80111 INTERIOR MATERIALS(CK22)
T2392-80111 INTERIOR MATERIALS(CK22H)
T2391-01111 SPARE KIT(CK22/CK22H)
KIOTI TRACTOR DIVISION /DAEDONG-USA, INC.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1877 GO KIOTI
Tel:1-919-374-5100 Fax:1-919-374-5001
http://www.kiotitractor.com
8
1
19
OVERSEAS SERVICE DIVISION / DAEDONG INDUSTRIAL Co.,Ltd.
1-12, BUKRI, NONGONG, DALSUNG-GUN, DAEGU, KOREA
Tel:82-53-610-3350 Fax:82-53-610-3359
http://www.daedong.co.kr
Printed in Korea. Oct.2010
* Bolts and nuts are excluded from the above picture.
10
Next page▼
A CABIN ASS’Y
11
15
1
20
1
12
1
13
1
21
1
Part No.
Description
Q'TY
11
T2391-85151
GROMMET
1
12
T2391-85141
CAB. FRONT SEALING PLATE(RH)
1
12-1
01754-50620
FLANGE BOLT(M6X20L)
2
12-2
02751-50060
FLANGE NUT
2
13
T2131-85411
FRONT SEALING RUBBER 1
(300L)
2
14
T2131-85421
FRONT SEALING RUBBER 2
(170L)
2
15
T2391-85151
TRANSMISSION COVER
1
16
T2391-86211
SMV BRACKET SUPPORT PLATE
1
16-1
01754-50816
FLANGE BOLT(M8X16L)
2
17
T2391-86221
CLUTCH STOPPER
1
17-1
01023-50630
BOLT(M6X30L)
1
17-2
04013-50060
PLAIN WASHER
1
17-3
41011-5151_4
NYLON NUT
1
18
T2391-86231
FENDER SEALING PAD 1
(980L)
2
19
T2391-86251
FRONT SHIELD PLATE SEALING
PAD(1300L)
1
20
T2391-68151
PARKING BRAKE SUPPORT
1
21
T2391-89111
PARKING BRAKE SUPPORT BASE
1
21-1
01123-50825
BOLT(M8X25L)
2
22
T2391-33111
ACCELERATION PEDAL
1
23
T2391-86281
SMV BRACKET
1
Remarks
14
18
1
17
1
16
1
NO.
22
1
19
1
23
1
CK20HS/CK22H
only
CK22/CK22H only
CK20HS/CK22H
only
CK20S/20HS only
23-1
* Bolts and nuts are excluded from the above picture.
01123-50820
BOLT(M8X20L)
2
Next page▼
B INTERIOR MATERIALS
1
2
1
5
1
9
1
3
1
6
1
10
1
4
1
7
1
11
1
NO.
Part No.
Description
Q'TY
1
T2391-98151
FENDER REAR PAD(LH)
1
2
T2391-98161
FENDER REAR PAD(RH)
1
3
T2391-94111
INSTRUMENT PANEL COVER
1
4
T2391-96191
SEAT FLOOR COVER
1
5
T2391-98131
SEAT FLOOR COVER(REAR)
1
6
T2391-98111
FENDER COVER(LH)
1
7
T2391-98121
FENDER COVER(RH)
1
8
T2391-94151
INSTRUMENT PANEL
INNER PAD(MIDDLE)
1
9
T2391-94131
INSTRUMENT PANEL
INNER PAD(LH)
1
10
T2391-94141
INSTRUMENT PANEL
INNER PAD(RH)
1
11
T2391-94121
INSTRUMENT PANEL
INNER PAD(MIDDLE)
1
12
T2391-96111
STEP FLOOR PAD
1
13
T2391-96131
STEP FLOOR PAD
1
Remarks
CK20S/22 only
8
1
12
13
CK20S/22
only
14
15
1
16
1
17
1
18
14
T2391-96211
SEAT FLOOR FRONT PAD
1
15
T2391-96221
SEAT FLOOR
UNDER PAD
1
16
T2391-91251
SIDE COVER PAD(LH)
1
17
T2391-91261
SIDE COVER PAD(RH)
1
18
T2391-91111
ENGINE ROOM
COVER PAD(FRONT)
1
Next page▼
B INTERIOR MATERIALS
19
1
24
1
29
1
20
1
25
1
30
1
21
1
26
1
22
1
27
1
31
1
32
1
23
1
28
1
33
1
NO.
Part No.
Description
Q'TY
19
T2391-91121
ENGINE ROOM
COVER PAD(MIDDLE)
1
20
T2391-91131
ENGINE ROOM
COVER PAD(REAR)
1
21
T2392-96211
SEAT FLOOR
FRONT PAD
1
22
T2392-96221
SEAT FLOOR
UNDER PAD
1
23
T2392-96141
STEP FLOOR PAD(LH)
1
24
T2392-96151
STEP FLOOR PAD(RH)
1
25
T2392-96161
STEP FLOOR PAD(LH)
1
26
T2392-96171
STEP FLOOR PAD(RH)
1
27
T2391-91211
FRONT SHIELD PLATE 1
INSULATING BOARD(LH)
1
28
T2391-91221
FRONT SHIELD PLATE 2
INSULATING BOARD(LH)
1
29
T2391-91231
FRONT SHIELD PLATE 1 PAD(RH)
1
30
T2391-91241
FRONT SHIELD PLATE 2 PAD(RH)
1
31
T2392-96191
SEAT FLOOR COVER
1
32
T2392-96361
TRANSMISSION
COVER PAD(LH)
1
33
T2392-96351
TRANSMISSION
COVER PAD(RH)
1
34
T2392-96341
TRANSMISSION
COVER PAD(RH)
1
35
T2392-96331
TRANSMISSION
COVER PAD(UPPER)
1
36
T2392-96321
TRANSMISSION COVER PAD2
1
37
T2392-96311
TRANSMISSION COVER PAD1
1
38
T2131-95111
VELCRO(MALE)
1
8M
39
T2131-95121
VELCRO(FEMALE)
1
2M
38
1
34
1
35
1
36
1
37
1
39
1
Remarks
CK20HS/22H
only
CK20HS/22H
only
Next page▼
C SPARE KIT
1
6
11
2
7
12
3
4
8
13
5
9
10
14
15
14
NO.
Part No.
Description
Q'TY
1
T4682-87812
RUBBER 1
2
2
T4682-87821
RUBBER COVER
2
3
T4682-87831
RUBBER COLLAR
2
4
T4682-87841
RUBBER 2
2
5
T4920-87851
COLLAR
2
6
01133-51240
BOLT
4
7
01173-51440
BOLT
6
8
01173-51445
BOLT
2
9
01173-51690
BOLT
2
10
02176-50120
NUT
4
11
02176-50160
NUT
2
12
04013-50120
PLAIN WASHER
8
13
04512-50140
SPRING WASHER
8
14
04512-50160
SPRING WASHER
4
15
04013-50160
PLAIN WASHER
2
Remarks
* CF(Cabin front mounting set): 1, 2, 3, 4, 5, 9, 11, 14 (Please refer to "How to install")
Next page▼
3. how to install THE cabin
This symbol means ATTENTION! YOUR SATETY
IS INVOLVED.
The message that follows the symbol contains
important information about satety. Carefully
read the message.
Eu only
Us only
A20
BEFORE SERVICING AND REPAIRING
1. Read all safety instruction in this manual and be aware of
safety decal locations on your machine.
CABIN ASS’Y
2. General safety information.
A21-1
A23
A1
2. Thoroughly clean your work area and the machine.
3. Make sure the machine is on firm and level ground and
that the parking brake is set.
4. Lower the implement to the ground.
5. Stop the engine and remove the key.
6. Disconnect the negative battery cable.
A21
7. Place a "DO NOT OPERATE" tag in the operator station.
A23-1
WORKING SAFETY
A17
A17-1
1. Do not operate or service the machine while under the influence of alcohol, medications, or other sustances.
3. Never use improvised tools, parts or procedures. Use only
recommended tools appropriate to the work.
A19
C11
C14
4. Extra care should be taken to work safety when servicing
is done by two or more persons.
5. Always support the machine with safety stands rated for
the weight of the machine. Never work under a machine
that is supported solely with a jack.
C5
6. Do not touch any rotating or hot parts while the engine is
running.
C3
7. Escaping fluid (hydraulic oil) under pressure can penetrate
the skin causing serious injury. Relieve pressure before
disconnecting hydraulic or fuel lines. Tighten all connections before applying pressure.
C1
C4
A18
A17-3
A12-2
A22
INTERIOR MATERIALS
2. Never wear loose fitting clothing and always use safety
equipment appropriate to the job.
A17-2
A12
A10
A12-1
A10-2
A14
C2
C15
C8
DISPOSE OF FLUIDS PROPERLY
A15
A13
C13
1. Observe relevant environmental protection regulations
when disposing of oil. NEVER pour fluids onto the ground,
down a drain, or into any body of water.
A3
A5
A14
A13
A10-1
HST only
A6
A16
A4
C14
C7
C13
C6
C12
A4
C12
C10
SPARE KIT
C9
A2
(A1) CABIN
(A2) CABIN SUPPORT(LH)
(A3) CABIN SUPPORT(RH)
(A4) CABIN SUPPORT SPACER
(A5) HEATER HOSE D
(A6) PIPE BAND
(A7) WIRE HARNESS(ALTERNATOR)
(A8) WIRE HARNESS(TURN SIGNAL LAMP)
(A9) WIRE HARNESS(TURN SIGNAL LAMP)
(A10) FRONT SEALING PLATE(LH)
(A10-1) FLANGE BOLT(M6X20L)
(A10-2) FLANGE NUT
(A11) GROMMET
(A12) FRONT SEALING PLATE(RH)
(A12-1) FLANGE BOLT(M6X20L)
(A12-2) FLANGE NUT
(A13) FRONT SEALING RUBBER 1(300L)
(A14) FRONT SEALING RUBBER 2(170L)
(A15) TRANSMISSION COVER(CK20HS/CK22H only)
(A16) SMV BRACKET SUPPORT PLATE
(A16-1) FLANGE BOLT(M8X20L)
(A17) CLUTCH STOPPER
(A17-1) BOLT(M6X30L)
(A17-2) PLAIN WASHER
(A17-3) NYLON NUT
(A18) FENDER SEALING PAD 1(980L)
(A19) FRONT SHIELD PLATE SEALING PAD(1300L)
(A20) PARKING BRAKE SUPPORT(CK22/CK22H ONLY)
(A21) PARKING BRAKE SUPPORT BASE(CK22/CK22H ONLY)
(A21-1) BOLT(M8X25L)(CK22/CK22H ONLY)
(A22) ACCELERATION PEDAL(CK20HS/CK22H only)
(A23) SMV BRACKET(CK20S/CK20HS ONLY)
(A23-1) BOLT(M8X20L)(CK20S/CK20HS ONLY)
(B1) FENDER REAR PAD(LH)
(B2) FENDER REAR PAD(RH)
(B3) INSTRUMENT PANEL COVER
(B4) SEAT FLOOR COVER
(B5) SEAT FLOOR COVER(REAR)
(B6) FENDER COVER(LH)
(B7) FENDER COVER(RH)
(B8) INSTRUMENT PANEL INNER PAD(MIDDLE)
(B9) INSTRUMENT PANEL INNER PAD(LH)
(B10) INSTRUMENT PANEL INNER PAD(RH)
(B11) INSTRUMENT PANEL INNER PAD(MIDDLE)
(B12) STEP FLOOR PAD
(B13) STEP FLOOR PAD
(B14) SEAT FLOOR FRONT PAD
(B15) SEAT FLOOR UNDER PAD
(B16) SIDE COVER PAD(LH)
(B17) SIDE COVER PAD(RH)
(B18) ENGINE ROOM COVER PAD(FRONT)
(B19) ENGINE ROOM COVER PAD(MIDDLE)
(B20) ENGINE ROOM COVER PAD(MIDDLE)
(B21) SEAT FLOOR FRONT PAD
(B22) SEAT FLOOR UNDER PAD
(B23) STEP FLOOR PAD(LH)
(B24) STEP FLOOR PAD(RH)
(B25) STEP FLOOR PAD(LH)
(B26) STEP FLOOR PAD(RH)
(B27) FRONT SHIELD PLATE 1 INSULATING BOARD(LH)
(B28) FRONT SHIELD PLATE 2 INSULATING BOARD(LH)
(B29) FRONT SHIELD PLATE 1 PAD(RH)
(B30) FRONT SHIELD PLATE 2 PAD(RH)
(B31) SEAT FLOOR COVER
(B32) TRANSMISSION COVER PAD(LH)
(B33) TRANSMISSION COVER PAD(RH)
(B34) TRANSMISSION COVER PAD(RH)
(B35) TRANSMISSION COVER PAD(UPPER)
(B36) TRANSMISSION COVER PAD2
(B37) TRANSMISSION COVER PAD1
(B38) VELCRO(MALE)
(B39) VELCRO(FEMALE)
(C1) RUBBER 1
(C2) RUBBER COVER
(C3) RUBBER COLLAR
(C4) RUBBER 2
(C5) COLLAR
(C6) BOLT
(C7) BOLT
(C8) BOLT
(C9) BOLT
(C10) NUT
(C11) NUT
(C12) PLAIN WASHER
(C13) SPRING WASHER
(C14) SPRING WASHER (C15) PLAIN WASHER
196S001A
Next page▼
1. Park the vehicle on firm and level ground. Then, engage the parking brake and stop the engine.
196S002A
2. Open bonnet and remove the negative
cable(1) of battery.
REMARKS
When attaching cabin and loader
simultaneously, make sure to attach
the loader first and then assemble
cabin.
196S003A
3. R e m o v e R O P S, R O P S b r a c k e t
(1)(left)(right), seat(2), rear mirror(3)
and turn indicator.
REMARKS
196S066A
4. After removing the bracket(1) and
increase A section hole to the dia. 20
mm(0787 in.), reinstall it. If the hole
is not expanded, it may be subject to
vibration.
196S004A
5. Pull out the mounting bracket assembly
cap of transmission case (left)(right)
and assemble front mounting cabin
s u p p o r t s p a c e r(A4) a n d c a b i n
support(A2,3) with. (C6,7,8,10,12,13)
196S005A
196S006A
6. Remove the clutch pedal holding
hook(1) and stopper(2).
After removing the rear mirror(3),
install it into the cabin.
196S007A
7. After loosening the locking bolt under
the seat and removing the seat bottom
panel, attach the seat floor under pad
(B15) and reassemble it.
REMARKS
How to attach sound absorbent
196S008A
8. After removing the rate of descent
adjusting lever(1) and pulling out
the differential motion locking pedal
spring(2), attach the seat floor front
pad(B14: mechanical model) inside
the seat bottom front cover.
196S009A
9. Remove the joystick lever cover(1)
and inside lever locking bracket. Then
pull out the floor mat(2) and remove
the instrument panel cover(3).
196S065A
10. After attaching the instrument panel
inner rubber pad(B11) and sound
absorbent(B8,9,10) inside the instrument
panel cover, reinstall it.
196S014A
196S012A
1. Wipe off the inside of the instrument
panel cover(1) cleanly.
2. After cutting the velcro(2)(B39) in a
proper size, paste it on the rubber
pad(3) along the edge of instrument
panel cover.
196S013A
3. Attach the rubber pad(3) inside of
instrument panel cover.
196S015A
196S011A
11. Using a hoist, support the stand and
hydraulic jack on the rear axle bottom
and remove the rear wheels.
196S010A
4. Attach the sound absorbent(4) to
the center, left and right side of
instrument panel cover.
12. Pull out the lever handle(1) of left/
right of fender and rate of descent
adjusting lever handle(2). Loosen
the fender handle locking bolt(3) and
lever guide locking screw(4) on the
fender bottom side to remove the
fender handle and lever guide.
Next page▼
REMARKS
196S016A
196S017A
13. A f t e r i n s t a l l i n g t h e s e a t f l o o r
cover(B4: mechanical type, B31: HST
type), paste the velcro enough to fix
it along the rim. Install the seat floor
cover(rear)(B5) in the same way.
196S021A
196S019A
CF : 1,2,3,4,5,9,11,14
196S018A
14. Assemble front left/right cabin mounting
cushion.
If you have the old hydraulic pipe (1),
please replace with new pipe. The
old pipe can interfere with front cabin
mounting.
Serial No. Break
Old pipe installed on :
CK20S : ~KS29-00232
CK20HS : ~KS30-00491
CK22 : ~KS32-00201
CK22H : ~KS35-00306
New pipe No. T2368-37082
196S023A
196S025A
196S024A
196S026A
15. Loosen the number plate bracket
locking bolt(1) and remove the number
plate bracket(2).
REMARKS
Number plate bracket Modification
16. With the cabin lifted up on hoist,
attach sealing pad(A19) and front
sealing rubber2(A14) as shown in the
figure.
17. Lower the cabin on the tractor slowly
and lock the front(CF), and rear(2)
mounting section.
196S022A
The number plate bracket should be
cut to assemble the cabin as shown
in the figure.
REMARKS
REMARKS (EU Only)
How to attach fender interior material
196S027A
18. Paste the velcro to fuel tank and the
fender.
196S031A
196S033A
051S002A
• Disassemble the cover(2) and cable(3)
from the removed parking brake lever
combination(1).
196S029A
Put the fender rear pad(B1,2) to the
gap between the fender and cabin
051S004A
• Af ter removing the par king brake
support(A20) and the parking brake lever
combination, connect them to the parking
brake support base. (A21-1)
21. Assemble joystick lever locking
bracket and install the cover(1).
196S032A
196S030A
196S028A
19. Attach the fender cover(B6,7) by
pasting velcro to left and right on the
fender.
First, attach velcro along the cabin
frame pipe. Then attach the edge of
interior material along with the velcro.
20. Punch bolt holes on the both lever
guide and assemble the lever
guide(1,2).
051S003A
• Assemble the parking brake suppor t
bas e(A21) an d t he rem ove d par k ing
brake bracket(4) on the panel of cabin
combination.
051S005A
• After reinstalling the brake cable and
cover, pull out the cable as shown in
the figure and connect the cable with
it.
Next page▼
REMARKS
REMARKS
A
196S034A
196S036A
B
196S035A
22. Attach the front sealing plate of cabin
(left)(A10), (right)(A12) with (A101,2)(A12-1,2).
Before installing the cover, first attach
the front sealing rubber(A13) to the
side of cover and then attach it with
the cabin.
196S037A
23. Lay out the sound adsorbent on the
step floor pad(B13) and install the
rubber step floor pad(B12). (mechanical
model)
196S043A
196S040A
196S038A
24. P a s t e Ve l c r o(B39) t o t h e c o v e r
surface of instrument panel and
attach the instrument panel cover
(B3).
196S039A
196S041A
196S042A
• I n s t a l l t h e c l u t c h s t o p p e r(A17) w i t h
(A17-1~3) as s h ow n i n f i g ur e(A). Fo r
long-tern storage, make sure to hang
the clutch pedal as shown in figure(B).
196S044A
1. For HST model, paste velcro(B39) inside
of transmission cover, and fit to the rubber
pad.
2. After attaching the rubber pad left, right,
top section inside the transmission cover,
paste interior sponge left, right, top section
on top of it. (B32~37)
REMARKS
196S045A
196S046A
25. A s s h o w n i n t h e f i g u r e, a t t a c h
the engine room cover pad to
b o n n e t(B18,19,20), s i d e c o v e r
p a d(l e f t)(B16)(r i g h t)(B17) a n d
front shield plate pad/insulating
board(B27,28,29,30).
196S047A
26. D i s c h a r g e r a d i a t o r c o o t a n t b y
opening the drain cork(1) on the
bottom of right side of the radiator.
Then remove the hose(2) between
water pump and cooling water
flange.
196S048A
27. Connect the heater hoseD(A5) to
heater connecting pipe that is in the
cabin left, right column respectively.
Then tie it with hose clamp (A6) and
insert the heater hose(1) of the right
side of cabin to the cooling water
flange side. After inserting the heater
hose(2) in the left of cabin to water
pump, secure it with bands. At this
moment, fix it by tying them after
pulling it inside, in order for the heater
hose not to interfere with cooling fan.
Fill the cooling water up to the normal
level after assembling heater hose.
196S051A
196S049A
196S050A
196S052A
Arrange the heater hose as shown in the
figure not to contact with muffler.
196S053A
Next page▼
USA Only
EU Only
196S054A
28. Connect the heat wiring(1) and wire
harness(alternator)(A7) on the left
cabin to connector. Connect the
mounting bolt under the starting
motor and magnet bolt(3) to a ground
wire. Remove alternator connector
(4) and then insert it to the extra
wiring connector(5). Then insert the
connector of extra wiring connector
(6). (tie the wiring using the cabin
support wiring guide).
196S055A
29. Install the brake light(2), connect
i t w i t h w i r i n g c o n n e c t o r. I n s e r t
grommet(A11) to the hole below.
051S006A
196S056A
30. Install the brake light(2), connect
i t w i t h w i r i n g c o n n e c t o r. I n s e r t
grommet(A11) to the hole below.
196S058A
32. Replace the seat inside the cabin,
and install respective lever handle.
REMARKS (USA Only)
REMARKS
Remove the turn signal light
installed on the equipment fender,
and install it as shown in the figure.
196S057A
31. After assembling the SMV bracket
s u p p o r t p l a t e(A16) b e h i n d t h e
fuel tank, install the name plate
bracket(1) and connect the wiring
connector. with (A16-1)
4. OPERATION INSTRUCTION
Indoor Lighting
Temperature Control Lever
196S059A
After attaching SMV emblem to SMV
bracket(A23), install SMV bracket to
tractor cabin towing hook as shown in
the figure.
Fuse Box
Front Glass Open/Close
Front Work Light Switch
ON
OFF
196S060A
(1) SWITCH COMBINATION
(2) COVER FOR AUDIO ASSEMBLY
(3) INDOOR LIGHTING
(4) VENT
(5) TEMPERATURE CONTROL KNOB
Press the right rim ( )
of indoor lighting once
to turn on the lamp and
press it again to turn it off.
Press On to turn on the front
work light and press OFF to
turn it off.
Heater flow amount adjusting switch
OFF
LOW
196S062A
Turn the switch to LOW to
Vent
Switch Combination
Turn the lever of vent left,
right and front, back to
adjust the direction of flow.
Wiper/Washer Fluid switch
ON
OFF
196S061A
(1) FRONT WORK LIGHT SWITCH
(2) HEATER FLOW AMOUNT ADJUSTING SWITCH
(3) WIPER/WASHER FLUID SWITCH
Press ON to activate the
wiper and continue to press
until the washer fluid comes
out. Press OFF to stop.
196S063A
Pull the fuse box cover(1) out to see attached
fuses of different values inside. Replace the
required fuse of standard capacity referring to
the size of fuse for each device on the cover.
HIGH slow the flow and turn it to
HIGH to fasten the flow.
Turn the lever counterclockwise
to increase the supply of
warm water that increase
the temperature of heater
flow. Turn it clockwise to
decrease the temperature.
<Fuse Capacity>
FUSE A : 10A ROOM LAMP, MEMORY
FUSE B : 15A CD PLAYER
FUSE C : 10A WORKING LAMP(FRONT)
FUSE D : 15A WIPER/WASHER
FUSE E : 15A HEATER
FUSE F : 10A BEACON LAMP(REAR)
FUSE G : 10A WORKING LAMP(REAR)
FUSE H : 10A SPARE
FUSE I : 15A SPARE
196S064A
Pull the open/close lever(1) of left and right
of front glass upward and push it forward to
fit it to the lever groove. Then the front glass
remains open. When closing, pull the lever
out of the groove, pull it backward and push it
downward to fit it to the groove.